Skip to content
Black Friday pricing on saunas, heaters and cold plunges, ends Nov 30. No code needed Free shipping to the 48 contiguous states

Installation and guides

Plan your sauna before it arrives: sizing, power, bases, chimneys, first use and care.

These guides help you plan and talk to your installer. They do not replace the manufacturer’s installation manual or your local building, electrical and fire codes, which always take precedence. Electric heaters must be connected by a licensed electrician.

Heater sizing

Every heater is rated by its manufacturer for a range of room volumes in cubic feet. To find your volume, multiply the inside length × width × height of the sauna room in feet. A 7 × 6 × 7 ft room is 294 cu ft.

  • Add about 50 cu ft for every 10 sq ft of glass, stone, tile or other uninsulated surface: these absorb heat.
  • Pick a heater whose rated range includes your adjusted volume. Near the middle of the range is ideal; for an outdoor sauna in a cold climate, stay out of the very top of the range.
  • Our heater sizing tool lists every heater we carry that is rated for your room, and each heater page has a fit check.
Room volumeTypical electric heaterTypical sauna size
Under 200 cu ft3.5 to 4.5 kW1 to 2 people
200 to 350 cu ft6 to 8 kW2 to 4 people
350 to 500 cu ft8 to 10.5 kW4 to 6 people
500 cu ft and up10.5 kW and up6 or more people, commercial rooms

These are typical values only. The manufacturer’s rated range for the exact model, shown on every heater page, is what counts.

Installing an electric sauna heater

Power

  • Residential sauna heaters run on 240V single-phase; some large heaters also come in 208V three-phase versions for commercial buildings.
  • Each heater page lists its current draw and the manufacturer’s wire size. Your electrician sizes the dedicated circuit and breaker from the manual and local code.
  • Heaters above about 9 kW often need a separate power or contactor box; the manual for each heater says when.

Controls

  • Heaters with built-in controls (for example Harvia KIP and Cilindro with knobs) need no separate control panel.
  • Heaters that use an external controller (Harvia Xenio or Fenix, HUUM UKU) need it to run. Heater packages include it. Controllers with Wi-Fi let you start the sauna from your phone.
  • The temperature sensor is mounted on the wall or ceiling where the manual shows. Its location matters for safe operation.

Placement and clearances

  • Follow the minimum distances in the manual from the heater to walls, benches and the ceiling. Many manufacturers recommend a safety railing around floor-standing heaters.
  • Most heaters are placed near the door with the fresh-air intake low, near or under the heater, and an exhaust vent high on the opposite wall.

Installing a wood-burning sauna stove

  • Base: the stove sits on a non-combustible floor or a protective base plate. Harvia and HUUM sell floor protection for this.
  • Clearances: keep the distances in the stove manual to combustible walls and benches, or install the maker’s protective sheath or heat shield to reduce them.
  • Chimney: use an insulated sauna chimney kit rated for the stove, through the roof or through the wall. Our stove packages include the chimney parts listed on the page.
  • Fresh air: plan an air intake near the stove so the fire draws properly.
  • Permits: many areas require a permit or inspection for a wood stove. Check with your local building or fire department before installing.
  • First fires: burn small, dry fires the first few times, with the door and vents open, to cure the paint. Some smell is normal.

A base for an outdoor sauna

An outdoor sauna needs a flat, level, well-drained base that can carry its weight (listed on every product page) plus people and stones.

  • Concrete pad: the most durable option. Slope it slightly so water drains away.
  • Pavers on compacted gravel: a common DIY base. Level it carefully; barrel cradles need full contact.
  • Deck: must be built for the load. Ask a builder to confirm it.
  • Keep the sauna clear of overhanging branches, and leave room around it to tighten barrel bands and maintain the wood.
  • Check HOA rules, setbacks and permit requirements for outbuildings in your area.

Assembling an outdoor sauna kit

  • Most barrel, cabin and cube kits are pre-cut and assemble with basic hand tools. Two adults can usually finish a barrel in a day; cabins take longer.
  • Barrel saunas are held together by stainless steel bands. Tighten them gradually as the staves settle, and again after the first weeks of use and seasonally.
  • Install the roof kit or shingles supplied with the sauna. An unprotected roof shortens the life of the wood and can void the warranty.
  • Electric heaters in outdoor saunas need a weather-rated supply run by your electrician.

Indoor, infrared and hybrid saunas

  • Measure the room, ceiling height and the doorways and hallway the panels must pass through. Allow clearance around and above the cabin as the manual specifies.
  • Infrared saunas plug into a dedicated outlet. The circuit and outlet type are listed on every product page. Never use an extension cord or power strip: it is unsafe and voids many warranties.
  • Indoor traditional and hybrid saunas with a Harvia heater need a dedicated 240V circuit for the heater, installed by a licensed electrician.
  • Indoor infrared saunas are for indoor use only unless the maker says otherwise.

Cold plunge setup

  • Place the tub on a level, solid surface that can carry the filled weight. Outdoors, keep it out of standing water and protect the chiller from direct weather as the manual advises.
  • Plug the chiller into the dedicated GFCI-protected outlet listed on the product page.
  • Fill with a garden hose, run the filter and sanitation system, and follow the maker’s water-care schedule. Drain and clean as the manual recommends.
  • Start with short plunges of 30 to 60 seconds and build up. If you have a heart condition or other health concerns, talk to your doctor before using a cold plunge or sauna.

Sauna stones

  • Use only stones made for sauna heaters, such as olivine diabase or peridotite. Ordinary rocks can crack or contain moisture.
  • Rinse the stones, then stack them loosely so air flows between them. Do not pack them tight or cover the heating elements.
  • Re-stack and replace crumbling stones about once a year with regular use.

First use

  • Run the heater empty (without people) for about an hour at full temperature with the vents open. A light smell from new heaters and wood is normal.
  • Traditional saunas usually run at 160 to 195°F; infrared saunas at 120 to 150°F. Most people enjoy two or three 10 to 15 minute rounds with cool-down breaks in between.
  • Pour water on the stones a little at a time with a ladle. Never pour water on an electric heater’s elements or on a heater not designed for it.

Care and maintenance

  • Sit on a towel; it keeps benches clean. Leave the door open after each session so the wood dries.
  • Do not varnish or paint interior wood. Lightly sand benches once a year if needed.
  • Outdoor saunas: treat exterior wood as the maker recommends, keep the roof in good condition, and re-tighten barrel bands seasonally.

Safety

  • Never leave a heater running unattended or with anything covering it.
  • Do not use a sauna after drinking alcohol. Drink water, and leave if you feel unwell.
  • Children should only use a sauna with an adult. Pregnant people and anyone with a medical condition should ask their doctor first.
  • Keep the clearances in the manual, and keep towels and clothing away from the heater.

Need help planning?

Call +1 (406) 582-7490 or email contact@saunabirch.com with your measurements and we will help you plan the install.